Best Maclaren Cup Holder (Maclaren Stroller Accessories)

QUESTION: IS THIS CUP HOLDER BIG ENOUGH TO HOLD GRANDE SIZED STARBUCKS COFFEE? WHAT ABOUT VENTI?
• Yes. The top part is flexible and keeps a snug fit even with bigger cups. I highly suggest this cupholder.
• I (carefully) put grande sized coffee from SB with no problem. If your beverage (no matter what coffee shop) comes with those sleeves, you might have to physically separate the top holder a bit for it to fit and sit properly on the base. They are slightly bendable, but firm. Of course, be careful of spilling hot coffee (or whatever) onto your child. Hope this is helpful!
• Absolutely! I use it all the time!
• This cup holder expands to fit lots of different size drinks.
• Hi Andy I believe the "tall" size would fit better. I can easily fit a 9 ounce feeding bottle from Avent. I do not think a grande sized cup would fit in there, although the top part of the holder is somewhat flexible to adjust itself to larger containers, but there is a limit for it. A venti surely will not fit in there. *Very important*: please keep in mind that this cup holder brings an important caution message carved on the lower part of it, clearly stating "NO HOT LIQUIDS". Maximum load: 1.1 lbs Please let me know if this has helped you. Best regards Sergio
#Maclaren_Cup_Holder_Charcoal

QUESTION: CAN THIS BE USED ON THE UPPABABY CRUZ STROLLER?
• This cup holder fits a square frame. It your stroller has a round frame, it definitely won't work.
• I don't believe Maclaren is compatible to Uppababy. The Maclaren strollers frame are shaped corner edges whereas the frame for Uppababy Cruz strollers are rounded edges. it will not connect and hold on the frame. Uppababy offers their own accessories and cup holder is available.
#Maclaren_Cup

QUESTION: HOW DO I PUT A CUP ON? I CAN'T SEEM TO SLIDE THE PIECE OUT...
• it's two pieces, slide them apart. Attach the part that goes around the side of the stroller onto the stroller and slide the cup holder back onto it. Hope this helps... it sits very good on the stroller.
• It is VERY VERY tightly attached so you have to push pretty hard to slide the pieces apart! It does eventually come apart though!
• If you put the cup holder to high on the stroller the handle will keep you from being able to put some cups in. If the cup holder is properly placed, you should be able to put in a reasonably sized cup by slightly spreading the cup holder sides.
#Holder_Charcoal_

QUESTION: DOES THIS WORK FOR THE MACLAREN MX3 (THE 3-WHEELER)? WHERE DOES IT ATTACH?
• If the the medal is square yes, if its round no. It goes on the side by the shade.
• I'm not familiar with that model; I use it on my Maclaren Quest. The part that clips onto the frame is square, and fits on a square frame (as opposed to being round, like most strollers). I have it attached to the frame, right below the handle.
#Maclaren_Cup_Review

QUESTION: HOW DOES THIS STAY UP ON THE MACLAREN STROLLER FRAME WITHOUT SLIDING DOWN?
• It locks on to the square tube of the handle and stays very firmly.
• It stays on as its wedged. Hard to describe, but the rectangular piece goes around the frame. The cup holder then slides on and basically serves as a clamp. We've used it for a few years and works well. It angles your beverage a bit, so be careful with open top items.
• Very sturdy! I've never experienced the cup holder sliding on my stroller. It has been so useful. In fact, I purchased 2 cup holder. One on each frame. This way, I can hold my childs and my own personal drink.
#Maclaren_Cup_Holder_Charcoal

QUESTION: CAN THIS BE ATTACHED [AS IS] TO A WALKER [ROUND TUBE]?
• Dear Customer, Thank you for your email. I can advise that the cup holder does attached onto the rear leg of our strollers so this would be a square tube and not round. I would think the cup holder would not fit a walker with rounded tubing. Kind Regards Sonia
• Unfortunately not, this specific for Maclaren strollers
#Maclaren_Cup

QUESTION: HAS ANYONE TRIED THIS CUP HOLDER ON THE MACLAREN MAJOR SPECIAL NEEDS STROLLER?
• I have one, but I'm using it on my maclaren techno. It nice to have. It sometimes gets in the way when putting away.
• Hi I have a quest which I use these for (and it doesn't interfere with opening/closing). I measured the bars that the cup holder sits on and it is 5/8" square, if that helps. The back of the cup holder slides off and is placed around the bar, and then the cup holder slides back on, locking in place. If your bar is about 5/8 of an inch then it should fit.
#Holder_Charcoal_

QUESTION: DOES THIS WORK WITH THE QUEST MODEL?
• Yes it will work on the MacLaren Quest Strollers. You simply just snap it on the vertical bar.
• It's for all Maclaren strollers
• Yes, that is where I installed mine. I believe it fits to any Maclaren stroller.
#Maclaren_Cup_Review

QUESTION: CAN I USE TWO OF THESE? WHERE DOES IT ATTACH
• It attaches to the frame of the stroller, where the maclaren logo/name is. So yes, you could attach 2, one on each side
• Yes, you can. I have two of these, one on each side of the stroller.
• It's not recommended but I use one on each side. There is a bracket that is placed on the side of the frame and you slide the holder into the bracket to lock it in place. Works great for me.
• Yes - you can use one of each side. It attaches to the frame of the stroller.

QUESTION: HAS ANYONE TRY THIS CUPHOLDER ON THE MACLAREN TECHNO XT, IS IT SUITABLE FOR IT?
• Yes